Tank and tankless installs, permitted and code-compliant across Collier County
When your old tank starts leaking or your hot water runs out mid-shower, our water heater installation Naples FL service gets a new unit in and running fast. We handle gas and electric, tank and tankless, for homeowners across Collier County. Same-day replacement is often available when you call before noon.
Water heater installation Naples FL is the removal of your old unit and the complete, code-compliant hookup of a new one, including the tank, supply lines, shut-off valves, venting, and the anode rod that protects the tank from corrosion. We drain and disconnect the old heater, inspect the pan and drain line, then set the new unit, connect gas or electric, and pressure-test every joint before we leave.
Naples homes deal with hard water and year-round heat that shorten tank life. Most tanks here fail between year 8 and 12, and when they go, they go fast, usually with a puddle in the garage or a water heater leak staining the closet floor. If you need water heater replacement Naples homeowners trust, we stock Rheem and A.O. Smith units locally so we are not waiting on a warehouse run.
A new water heater is not glamorous, but it changes your daily routine. Here is what you actually get when we swap the unit.
A correctly sized 50 gallon water heater installation Naples FL means back-to-back showers without the third person getting a cold surprise. We size the tank to your household count, not to whatever box is on sale, so recovery time matches how your family actually uses water.
Modern tankless and high-efficiency tank units cut standby heat loss. A Navien condensing unit can run 0.95 UEF, which trims the gas portion of your bill compared with a 12-year-old tank that reheats all day. Most Naples homeowners notice the difference within two billing cycles.
Old tanks rust from the inside out. Once you see water pooling or rust in the hot water, the steel is already thin. Replacing before a full burst protects drywall, flooring, and anything stored near the unit. We install a new pan and route the drain line so a future drip goes outside, not into your house.
Water heater replacement permits Naples Florida requires are part of the job, not an upsell. We pull the permit, meet the inspector, and leave you documentation that matters at resale. Unpermitted swaps can stall a home sale or void insurance coverage after a leak claim.
From the first call to the final test, here is exactly what happens when we install your new water heater in Naples.
We ask about your current unit, fuel type, household size, and where the heater sits. That tells us whether you need a standard 40 or 50 gallon tank or a tankless unit, and whether we can schedule same day water heater replacement Naples FL. Most calls take under 10 minutes.
A licensed technician confirms the flue, gas line size, electrical circuit, and clearance. We check your water pressure gauge reading and look for corroded pipes or a failing shut-off valve that should be replaced while we are in there. You get a firm price before any work starts.
We shut the water, drain the old tank, and disconnect gas or power. The old unit comes out, the pan gets cleaned or replaced, and we inspect the drain pan line and floor for hidden water damage. This stage usually runs 45 to 90 minutes.
The new heater goes in, level and strapped per Florida Building Code. We use copper pipe or PEX piping depending on your setup, new supply lines, a fresh Teflon tape seal on threaded joints, and a new anode rod. Gas units get a proper vent and drip leg; electric units get a matched breaker and disconnect.
We fill the tank, purge air from the lines, and fire the burner or element. A water pressure gauge confirms normal operating pressure, and we check every fitting with a dry rag for weeping. You get a walkthrough of the thermostat setting, the shut-off location, and your warranty paperwork.
Our technicians hold Florida Plumbing License credentials and work under a Master Plumber License on every permitted job. We install to Uniform Plumbing Code (UPC) and Florida Building Code standards, which matters in Collier County where inspectors check venting, T&P relief lines, and expansion tanks closely. We have swapped tanks in garages, closets, attics, and tight condo mechanical rooms across Naples, and we carry the press tool, soldering torch, and PEX crimper to handle copper, CPVC, or PEX without a second trip.
We are a local crew, not a call center. When you book water heater installation Naples FL with us, the person who answers the phone is the person who knows your job.
Call before noon and we can often complete same day water heater replacement Naples FL. We stock common tank sizes on the truck, so a failed heater in the morning usually means hot water by dinner. Emergency calls after hours get routed to a live technician, not a voicemail.
We pull the water heater replacement permits Naples Florida requires and meet the inspector on site. You do not chase paperwork or wonder if the job was done legally. That documentation protects you at resale and with your insurance carrier if a leak ever happens.
Tankless water heater installation Naples requires gas line sizing, venting, and condensate handling that standard swaps do not. We run the load calculation, upsize the gas line when needed, and mount the unit so service access stays clear. Navien and Rheem condensing units are our most common installs.
You get a firm number before we start, based on tank size, fuel type, and any code corrections. No hourly surprise, no parts markup revealed at the end. If we find corroded pipes or a bad shut-off valve during removal, we quote it before touching it.
Every install covers the full job, not just the tank swap. Here is what comes standard when we replace your water heater in Naples.
Your new Rheem, A.O. Smith, or Bradford White unit arrives with a fresh anode rod installed. That rod is what sacrifices itself to corrosion so the tank does not. We check it at every service visit and can swap it to extend tank life.
We pull the Collier County permit and meet the inspector on site. You get the signed-off documentation for your records. This is included in the price, not billed as a separate line item after the fact.
Old supply lines and shut-off valves are a leading cause of leaks after a new install. We replace them with new braided or copper lines and a fresh valve so the connection points are as new as the tank itself.
Gas units get a properly sized vent, drip leg, and sediment trap per Uniform Plumbing Code. We test for leaks at every joint with a pressure gauge and soap solution before we consider the job done.
The old tank leaves with us. We sweep the area, wipe down the pan, and leave the space cleaner than we found it. You do not need to schedule a separate pickup or haul a 150-pound tank to the curb.
We register your manufacturer warranty and hand you the paperwork. Tank warranties typically run six to twelve years depending on the model, and labor coverage is included on our workmanship. Keep the documents for resale.
Most people call us when something has already gone wrong. Here are the problems we hear about most in Naples, and how a proper install fixes them.
Rust in the hot water means the tank lining has failed. The unit is on borrowed time and could leak through the bottom at any point, damaging flooring and drywall.
We confirm the tank is the source, not the pipes, then replace the unit. A new tank with a fresh anode rod restores clean hot water immediately. If the rust traces to corroded pipes, we quote pipe repair or repiping before the install.
That noise is sediment boiling under the burner. It wastes gas, reduces hot water capacity, and overheats the tank bottom, which shortens its life by years.
In hard-water areas like Naples, sediment builds fast. We drain and flush the tank first. If the buildup is heavy or the unit is past year eight, replacement is the better spend. We also install a pan and check the drain line while we are there.
An undersized or failing heater means cold showers, especially with guests or a full house. It usually signals the tank is scaling up or the dip tube has failed.
We measure your first-hour rating and household demand, then size the replacement correctly. A 50 gallon water heater installation Naples FL often solves it for a family of four. Larger households may be better served by a tankless unit.
A leaking tank will not heal. It can flood a closet or garage, ruin stored items, and in an attic unit cause ceiling damage that costs far more than the heater itself.
We shut the water, drain the unit, and replace it. We also inspect the pan and drain line, and check for a slab leak or supply line drip that may have contributed. New shut-off valves go in so you can isolate the heater in seconds next time.
We treat it as urgent, shut the water, and schedule a same-day or next-morning replacement. We bring a 50 gallon Rheem unit, new pan, and new supply lines, and pull the permit the next business day.
Hot water is restored within 24 hours, the garage floor stays dry, and the job is permitted and inspected for resale.
We run a first-hour rating calculation and recommend either a 75 gallon tank or a Navien tankless unit. We explain the gas line and venting requirements for each option before you choose.
Back-to-back showers and laundry run without a cold finish, and the gas bill drops compared with the old tank.
We provide our Florida Plumbing License and insurance certificates to the association, pull the Collier County permit, and coordinate access with building management for the install day.
The unit is replaced without association pushback, the inspector signs off, and the owner has documentation on file.
We prioritize the call, confirm the tank size over the phone, and dispatch with the right unit on the truck. We handle the permit and send the landlord the paperwork afterward.
The tenant has hot water the same day, and the landlord avoids a habitability complaint and a rent credit request.
Connects copper and PEX fittings without an open flame. Faster and safer in tight closets and attics where a soldering torch is risky near framing or stored items.
Used for copper pipe joints where a sweated connection is the right call. We keep a fire blanket and extinguisher on hand any time the torch comes out.
Crimps PEX rings for supply line connections. PEX piping handles Naples water chemistry well and flexes around tight runs without extra fittings.
Reads your home's static and working pressure. High pressure above 80 psi shortens heater life and can void warranties, so we check it on every install.
Listens for hidden leaks in walls and slabs before we set a new heater. Finding an existing leak first prevents callbacks and protects your new unit.
Standard workhorses for gas and water connections. We carry a full range of pipe fittings, Teflon tape, and plumber's putty so we finish in one trip.
Every install follows UPC requirements for T&P relief valve piping, expansion tanks, venting, and clearances. Collier County inspectors check these items, and we build to code the first time so there is no re-inspection fee or delay.
Florida Building Code requires proper flue termination, combustion air, and seismic strapping on water heaters. We strap every unit and verify vent slope and clearance so the install passes inspection without a correction notice.
We size by first-hour rating rather than tank volume alone. That number accounts for recovery speed and household demand, which is why a 50 gallon tank can outperform a 60 gallon unit with a weaker burner.
After connection, we pressurize the system, purge air, and check every joint with a dry rag and soap solution. A water pressure gauge confirms normal operating range before we call the job complete.
Naples water is hard, and that single fact drives most of what we see. Sediment builds on the tank bottom faster here than in softer-water markets, which is why we recommend an annual flush and why so many tanks fail between year 8 and 12. The climate adds its own wrinkle: heaters in garages and attics deal with heat and humidity year-round, and a unit that sits in a 120-degree attic works harder than one in a conditioned closet. We install to Florida Building Code and Uniform Plumbing Code, and Collier County inspectors check T&P relief piping, expansion tanks, and venting on every permitted job. If you are comparing tankless vs traditional water heater in Naples, the answer usually comes down to household size and gas capacity. A tankless water heater installation Naples FL job needs a proper load calculation and often a gas line upsize, but it eliminates standby loss and never runs out. For smaller homes or rentals, a standard 50 gallon tank is still the practical choice.
Many homes here have garage-mounted heaters with easy access. We can usually complete a standard swap in under four hours and coordinate with HOA rules on visible venting.
Condo and villa units often sit in tight mechanical closets. We measure clearance and confirm building approval before scheduling, and we carry compact units for tight fits.
Larger homes with high hot-water demand. We frequently recommend 75 gallon tanks or tankless systems here, and we check gas line capacity before quoting.
Older housing stock with galvanized or early CPVC lines. We inspect supply piping during the install and often pair the heater with pipe repair or a partial repipe.
A mix of rentals and owner-occupied homes. Landlords appreciate our same-day options and the permit paperwork we provide for their records.
Sediment shortens tank life and reduces capacity. We flush tanks during service and recommend annual maintenance to protect your investment.
Attic units risk ceiling damage if they leak, so we always install a pan and route the drain line to a safe location. Garage units need strapping and vent checks.
Heaters work harder in unconditioned spaces. We check venting and combustion air carefully on gas units to prevent backdrafting and premature failure.
A family of four had a leaking 40 gallon tank in the garage, rust-colored hot water, and popping sounds for weeks. The base was weeping and the pan had standing water. They were taking cold showers by the time they called.
We removed the old unit, replaced the pan and drain line, and installed a 50 gallon Rheem tank with new supply lines and shut-off valves. The job took three hours, passed inspection, and restored hot water the same afternoon.
Flush the tank annually to clear sediment, and check the anode rod at year five. With Naples water, that routine typically adds three to five years to tank life.
A couple in a three-bath villa kept running out of hot water with a 15-year-old tank. They wanted endless hot water but worried about gas capacity and venting in a tight mechanical closet.
We ran a load calculation, upsized the gas line, and installed a Navien condensing unit with new venting and condensate handling. The install took seven hours and passed inspection. Hot water is now continuous at every fixture.
Descale the heat exchanger once a year with a vinegar flush kit. In hard-water Naples, that single step protects the unit and keeps efficiency near its rated 0.95 UEF.
A landlord had a failed heater in a rental and a tenant without hot water for two days. The old unit was a 12-year-old tank with corroded supply lines and a seized shut-off valve.
We replaced the tank with a 40 gallon A.O. Smith unit, installed new supply lines and a working shut-off valve, and pulled the permit the same week. The tenant had hot water by 4 p.m. and the landlord received the inspection paperwork.
We set a reminder for an annual flush and check the T&P valve at each visit. For rentals, that schedule prevents emergency calls and keeps turnover predictable.
Typical 2026 pricing in Naples runs $1,200 to $2,400 for a standard tank replacement and $2,800 to $4,500 for a tankless conversion, including the permit and haul-away. The spread comes down to tank size, fuel type, and whether we find corroded pipes or a failed valve during removal. We give you a firm number before we start, so the price you hear is the price you pay. Water heater replacement cost Naples, Florida homeowners see varies most by whether the job is a straight swap or a conversion.
A 40 gallon tank costs less than a 75 gallon unit, and a high-efficiency model costs more than a standard one. We size to your household so you are not overpaying for capacity you will never use.
Electric installs are usually simpler and cheaper. Gas water heater installation Naples jobs need venting, a drip leg, and sometimes a gas line upsize, which adds labor and materials.
Switching from tank to tankless adds venting, condensate handling, and often a gas line upgrade. The higher upfront cost is offset by lower energy use and a longer service life.
Missing expansion tanks, improper T&P piping, or unstrapped units must be corrected to pass inspection. We quote these before starting so there is no surprise on the invoice.
A garage unit is straightforward. An attic or tight condo closet takes longer and may require a second technician, which affects labor. We confirm access during the phone assessment.
The Collier County permit fee and old tank disposal are included in our quote. You do not need to haul a 150-pound tank to the curb or schedule a separate pickup.
$1,200 - $4,500 depending on tank size, fuel type, and whether it is a swap or a tankless conversion
Based on scope and requirements
A new heater protects your floors, restores hot water, and typically cuts the gas or electric portion of your bill. With annual flushing, a quality tank lasts 10 to 12 years in Naples water, which works out to a modest cost per year of reliable hot water.
Most standard tank replacements run $1,200 to $2,400 installed, including the permit and haul-away. Tankless water heater installation cost Naples homeowners see typically lands between $2,800 and $4,500 because of venting and gas line work. Exact pricing depends on tank size, fuel type, and whether we find corroded pipes or a bad valve during removal.
A straight tank swap takes two to four hours. Tankless conversions run five to eight hours because we upsize the gas line, run new venting, and handle condensate. If your unit sits in an attic or a tight condo closet, add an hour for access. We schedule most installs as a single visit and test everything before we leave.
Yes. Collier County requires a permit for water heater replacement, and the work must meet Florida Building Code and Uniform Plumbing Code standards. We pull the permit for you and meet the inspector on site. Skipping it can void insurance coverage after a leak claim and complicate a home sale when a buyer's inspector flags unpermitted work.
A 40 gallon tank fits one to two people, a 50 gallon water heater installation Naples FL suits three to four, and five or more people usually need a 75 gallon tank or a tankless unit. We size by first-hour rating, not just tank volume, because Naples households run showers, laundry, and dishwashers at the same time.
Replaced our water heater in North Naples the same day we called. They pulled the permit, hauled the old tank, and cleaned up the garage better than they found it. Fair price and no upsell pressure.
Switched us to a tankless unit in Pelican Bay. The technician explained the gas line work clearly and finished in a day. Hot water never runs out now, and the inspector signed off without issues.
We manage rentals in East Naples and use them for heater replacements. They show up on schedule, handle permits, and send the paperwork. That reliability is hard to find.
Our 12-year-old tank started leaking on a Friday. They had a new 50 gallon unit in by Saturday afternoon. Clear pricing, no surprises, and they showed me how to shut it off.
A burst pipe or failed heater at 2 a.m. needs a live technician, not a callback. We handle emergency water heater leaks, burst pipe repairs, and shut-off failures across Naples, and we can often pair an emergency repair with a same-day replacement.
Emergency Plumbing ServicesSediment from an old tank can settle in your lines and slow drains. When we install a new water heater, we can hydro jet the nearby drain run or clear a slow shower line so the whole system starts fresh.
Drain CleaningIf a sewer backup or root intrusion has you pulling fixtures, it is a smart time to replace an aging water heater. We scope the line with a sewer camera and handle both jobs in one visit to cut repeat disruption.
Sewer Line RepairNot every failing heater needs replacement. If your unit is under eight years old, we diagnose the element, thermostat, or gas valve first. Repair is often the smarter call, and we tell you honestly when replacement makes more sense.
Water Heater RepairA water heater leak is easy to spot, but slab leaks and hidden supply line drips are not. We use a leak detection microphone and pressure testing to find the source before we install, so a new heater does not sit on top of an unresolved problem.
Leak DetectionOld galvanized or corroded pipes reduce flow and shorten heater life. During installation we inspect the supply lines and repair or replace any section that shows scale, pinholes, or low water pressure before connecting the new unit.
Pipe RepairHomes with failing CPVC or galvanized lines often pair a repipe with a new heater. We run PEX piping or copper pipe through the house, then tie in the new unit, so you get consistent pressure and clean hot water from every fixture.
RepipingA running toilet wastes water and can mask pressure issues. If we are already in the house for a heater install, we can replace a wax ring, flapper, or fill valve and check that supply lines are not restricting flow.
Toilet RepairNew heaters expose weak fixtures. If your Moen or Delta faucet drips or the cartridge is scaled up, we can swap it during the same visit so you are not scheduling a second appointment for a small fix.
Faucet RepairA jammed disposal or leaking flange under the sink often shows up alongside heater work in the same utility area. We clear jams, reseal the flange, and check the supply lines while the tools are already out.
Garbage Disposal RepairRestaurants, salons, and small hotels in Naples need hot water that never quits. We install commercial-grade Rheem and Bradford White units sized for peak demand, with the venting and gas capacity to match, and we schedule around your business hours.
Commercial PlumbingReal experiences from customers who chose our Water Heater Installation services
Our 11-year-old tank let go on a Saturday morning and flooded the garage. I called at 9 a.m. and they had a new 50 gallon Rheem in and running by 2 p.m. the same day. They pulled the permit, hauled the old unit away, and showed me the shut-off valve before leaving. No mess left behind.
Homeowner, North Naples
We switched from a tank to a Navien tankless unit and I was worried about the gas line. The technician ran the load calculation, upsized the line, and handled the venting through the side wall. Took most of a day but the hot water is endless now. He explained the thermostat settings clearly.
Homeowner, Pelican Bay
I manage several rentals and use them for water heater replacement across East Naples. They pull permits, meet the inspector, and send me the paperwork every time. Pricing is firm and they show up when they say. That reliability matters when you are coordinating with tenants.
Property Manager, East Naples
Our 11-year-old tank let go on a Saturday morning and flooded the garage. I called at 9 a.m. and they had a new 50 gallon Rheem in and running by 2 p.m. the same day. They pulled the permit, hauled the old unit away, and showed me the shut-off valve before leaving. No mess left behind.
Homeowner, North Naples
We switched from a tank to a Navien tankless unit and I was worried about the gas line. The technician ran the load calculation, upsized the line, and handled the venting through the side wall. Took most of a day but the hot water is endless now. He explained the thermostat settings clearly.
Homeowner, Pelican Bay
Cold showers end when you call us. We install tank and tankless units across Collier County, pull the permit, and test every connection before we leave. Call (239) 522-0938 and we will give you a firm price and a real arrival window.